This guide shows how to wire a Teltonika RUT240 or RUT241 cellular router to Swiftlane's Lysora hardware (the LCS switches or the LR300G-P router) and how to connect a Swiftreader X or Swiftvision device to complete the installation. It is written for installers on site and for the Support team.
Some properties have the building's own managed internet, with the Teltonika as the fallback. Others use the Teltonika as the only internet source. The wiring to the Lysora hardware is the same in both cases. What matters is which port you use on the Lysora switch or router.
How it all connects
The Teltonika gets internet from the building (when the building has it) or from the cellular network. The Lysora switch or router shares that internet with every device connected to it, and powers the Swiftreader X or Swiftvision over PoE+ through the same cable.
Quick answer
Building internet (if the property has it): into the WAN port of the Teltonika.
LCS switches (LCS-4GS-P, LCS-8GS-P, LCS-16GS-P, LCS-24GS-P): Teltonika LAN port to a non-PoE port.
LR300G-P router: Teltonika LAN port to the port labelled WAN, next to port 9.
Swiftreader X or Swiftvision: a PoE+ port on the Lysora switch or router.
If the building has its own internet
When the building provides its own managed internet connection, the Teltonika is the fallback:
Connect the building's internet to the WAN port of the Teltonika.
Connect the LAN port of the Teltonika to the Lysora hardware exactly as shown in this guide (a non-PoE port on an LCS switch, or the WAN port on the LR300G-P).
The Teltonika uses the building internet first. If the building internet goes down, the Teltonika switches over to cellular by itself. Nothing changes on the Lysora switch or router, because it is always connected to the Teltonika LAN port.
If the property has no building internet, the Teltonika is the only source and uses cellular. The Lysora wiring is identical.
When this applies
Use this guide only when the property is set up with a Teltonika RUT240 or RUT241 cellular router. Every property is different: some have only the building's own internet and no Teltonika, some use the Teltonika as the fallback for the building internet, and some use it as the only internet source. If there is no Teltonika on site, this guide does not apply.
LCS switches: use a non-PoE port for the Teltonika
These models are switches only. The Teltonika feeds internet into a non-PoE port, and the switch passes it on to every device connected to it. Devices receive their IP addresses from the Teltonika automatically.
Connect a cable from the LAN port of the Teltonika to a non-PoE port on the switch.
Connect the Swiftreader X or Swiftvision to a PoE+ port on the switch. The switch powers the device through the cable.
Check that the device powers on and has internet (see "Check the installation" below).
Warning: never connect the Teltonika to a PoE+ port. The port can send power into the cellular router and burn it out.
LCS-4GS-P
LCS-8GS-P
LCS-16GS-P
LCS-24GS-P
LR300G-P router: use the WAN port for the Teltonika
The LR300G-P is a router and a switch in one. It must receive the Teltonika internet on its WAN side, not on a numbered port.
Find the port labelled WAN, right next to port 9.
Connect a cable from the LAN port of the Teltonika to the WAN port.
Connect the Swiftreader X or Swiftvision to a PoE+ port on the router. The router powers the device through the cable.
Check that the device powers on and has internet (see "Check the installation" below).
Common mistake: Teltonika in a numbered port on the LR300G-P
Because the LR300G-P is also a router, its numbered ports belong to its own network. If the Teltonika LAN cable is plugged into a numbered port (for example port 8), the device ends up on two different networks at once. This is a subnet conflict, and it happens even when no firewall or other restriction is set on the Teltonika.
Impact: when the subnet conflict occurs, the Lysora device shows as offline on the Lysora portal.
How to spot it (support team):
The Lysora device shows as offline on the Lysora portal.
At the Teltonika, the same Lysora device appears with two IP addresses on different subnets, for example 192.168.1.10 and 192.168.100.1.
Fix: move the Teltonika LAN cable from the numbered port to the WAN port. The device should come back online on the portal once the conflict clears.
Check the installation
The Swiftreader X or Swiftvision powers on.
The device has internet and receives an IP address.
The Lysora device shows online on the Lysora portal.
Troubleshooting
Lysora device offline on the portal (LR300G-P): check that the Teltonika LAN cable is in the WAN port and not in a numbered port.
Swiftreader X or Swiftvision has no power: check that it is connected to a PoE+ port, not to the port used for the Teltonika.
Teltonika not working after installation: check that its LAN cable is not in a PoE+ port, and replace the Teltonika if it was.
Installer checklist
Model checked on the label: LCS switch or LR300G-P.
Building internet (if any) is connected to the Teltonika WAN port.
LCS switch: Teltonika LAN is in a non-PoE port, not a PoE+ port.
LR300G-P: Teltonika LAN is in the WAN port, not a numbered port.
Swiftreader X or Swiftvision is connected to a PoE+ port and powers on.
Device has internet and shows online on the Lysora portal.
Photo of the cabling added to the job record.






